Howard Miller Quartz – Dual Chime Clock Movement
Posted on July 9, 2013 | By clockde
Howard Miller Quartz – Dual Chime Clock Movement
1. OPERATING INSTRUCTIONS
a) Release the pendulum guide (for pendulum movements only) from the transport-locking pin by gently pushing it sideways, allowing the guide to hang freely. Hang the pendulum on the pendulum guide.
b) If the speaker is mounted directly to the quartz movement, the speaker will need to be temporarily removed in order to install the batteries. Grasp around the outer edges of the speaker with your fingers and pull gently. Care should be taken not to damage the center of the speaker. Replace the speaker after the batteries have been installed and chime selection options are set.
Install two “C” size Duracell brand alkaline batteries according to the +/- symbols in the battery holders.
2. SETTING THE TIME
Adjust the time by using the minute hand or the Time Setting knob. Never turn the hour hand to set the time; it will turn automatically with the minute hand. Turn the Time Setting knob or move the minute hand (AFTER the batteries have been installed) so that the hands rotate clockwise. When setting the time, the clock will not chime at the ¼, ½, or ¾ hour positions.
When manually setting the time, the clock may chime a few minutes before or after the hour – this will automatically be corrected during the first hour of normal operation. The clock may also chime out of sequence during the first hour of operation. After setting to the correct time, it is important that the clock movement be allowed to operate for at least one hour for the chime sequence to become fully functional. The quartz movement is highly accurate and has been adjusted at the factory for precise time keeping.
3. CHIME MELODY
Use the switch with the symbols OFF, WEST, and MELODY2 to select the chime melody according to the following settings:
OFF = Silent
WEST = Westminster melody and full hour strike
MELODY2 = Ave Maria melody and full hour strike (Beethoven’s Ode to Joy on select models)
4. VOLUME CONTROL
The volume of the chime can be modified by turning the Volume Control knob.
5. AUTOMATIC NIGHTTIME CHIME SHUT-OFF
The movement has automatic nighttime volume shut-off or volume reduction options for a period of eight (8) hours after the switch is moved to the shut-off or volume reductions positions. This feature will automatically repeat at the same time every 24 hours. Use the switch with the Night time shutoff positions symbols to select chime silencing according to the following settings:
Use the switch with the symbols to select chime silencing according to the following settings:
If you wish to start the night-time silence at 10:00, please do the following:
1) Set the chime switch in the back to the note on the far right (there are
three positions on this switch).
2) just before 10:00PM (9:50ish) , move the switch all the way to the left.
The clock will then remember to turn off at 10:00 and come back on after
6:00AM.
This will set the start time for the chime shutoff at 10:00 for an eight hour duration.
6. OTHER FEATURES
This movement features a 4/4 chime melody. The movement plays ¼ of the melody at quarter past the hour, ½ the melody at half past the hour, ¾ of the melody at three-quarters past the hour, and the full melody on the hour. Following the melody on the hour is the count hour strike. Slide the 4/4 Chime Selection switch to the 1/4 position to only play the full melody and hour strike.
Slide the 4/4 Chime Selection switch to the 4/4 position to play the melody at every quarter hour as previously described.
***Always use Duracell Brand Size “C” Batteries as Energizers and other brands may not function properly in this movement.
7. BATTERY REPLACEMENT
If the clock begins to loose time, chime weakens, or pendulum stops to swing, this is the sign of weak or exhausted batteries. Replace the batteries with 2 fresh “C” size alkaline batteries. Always use Duracell brand batteries. Other brands may cause the clock to fail.
Recent Comments